NTNUJAVA Virtual Physics Laboratory
Enjoy the fun of physics with simulations!
Backup site http://enjoy.phy.ntnu.edu.tw/ntnujava/

Easy Java Simulations (2001- ) => Electronic => Topic started by: Fu-Kwun Hwang on October 17, 2007, 10:00:46 pm



Title: Common Emitter Transistor Amplifier
Post by: Fu-Kwun Hwang on October 17, 2007, 10:00:46 pm
The following java simulate a "Common Emitter Transistor Amplifier".
The Gain is mainly control by RE1 and Rc, G=RC/RE1
(1st order approximation: Assume RL>>Rc, and R1,R2 >> RE1,Rs<
R1 and R2 is used to set up the bias voltage. VB=Vcc*R2/(R1+R2);
RE1+RE2 in series to make the circuit more stable (provide feedback).
RE2 in parallel with a CE to short circuit the AC signal, so the gain is not dependent on RE2.

You can adjust RE1 and RC to control the GAIN of the amplifier, however if the Gain is too large (or biased voltage is not set up property), some voltage will be cutoff or make the transistor saturate (it will burn out in real life, the color will turn RED in the simulation).
(Because VC output can not be larger than Vcc (or IC=0 which is cutoff region),
and VC can not be smaller than VE+0.2V which will run into saturation and the transistor will burn out.
So the proper adjustment with R1,R2 will increase the working region of the amplifier.
Have fun with the following circuit!
-*-
You are welcomed to check out The Common Emitter Amplifier Circuit (http://www.phy.ntnu.edu.tw/ntnujava/index.php?topic=2116.msg7909#msg7909) to learn how to set up the DC biased circuit setup.


Title: Re: Common Emitter Transistor Amplifier
Post by: quentin on September 17, 2009, 10:17:42 pm
If I run this simulation in my browser before logging in I see the controls and oscilloscope display. But, if I run this simulation in my browser while logged in, I only see the circuit. The same problems happens if I run it on my desktop. What's wrong?


Title: Re: Common Emitter Transistor Amplifier
Post by: Fu-Kwun Hwang on February 26, 2011, 04:39:37 pm
I did not find similar problem with my browser. Did any one else has similar problem?


Title: Re: Common Emitter Transistor Amplifier
Post by: anilchaubey on January 11, 2015, 10:15:44 pm
The following java simulate a "Common Emitter Transistor Amplifier".
The Gain is mainly control by RE1 and Rc, G=RC/RE1
(1st order approximation: Assume RL>>Rc, and R1,R2 >> RE1,Rs<<R1 or R2).

R1 and R2 is used to set up the bias voltage. VB=Vcc*R2/(R1+R2);
RE1+RE2 in series to make the circuit more stable (provide feedback).
RE2 in parallel with a CE to short circuit the AC signal, so the gain is not dependent on RE2.

You can adjust RE1 and RC to control the GAIN of the amplifier, however if the Gain is too large (or biased voltage is not set up property), some voltage will be cutoff or make the transistor saturate (it will burn out in real life, the color will turn RED in the simulation).
(Because VC output can not be larger than Vcc (or IC=0 which is cutoff region),
and VC can not be smaller than VE+0.2V which will run into saturation and the transistor will burn out.
So the proper adjustment with R1,R2 will increase the working region of the amplifier.
Have fun with the following circuit!
-*-
You are welcomed to check out The Common Emitter Amplifier Circuit (http://www.phy.ntnu.edu.tw/ntnujava/index.php?topic=2116.msg7909#msg7909) to learn how to set up the DC biased circuit setup.
it would be better if capacitors are removed and cell connection provisions are made instead then it would suit to plus two level teaching in india